View M36P0R9060N0ZANE_4641352.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

M36P0R9060N0
512 Mbit (x16, Multiple Bank, Multi-Level, Burst) Flash memory 64 Mbit (Burst) PSRAM, 1.8V supply, Mux I/O, Multi-Chip Package
Preliminary Data
Feature summary
Multi-Chip Package - 1 die of 512 Mbit (32Mb x 16, Multiple Bank, Multi-Level, Burst) Flash memory - 1 die of 64 Mbit (4Mb x16) PSRAM Supply voltage - VDDF = VCCP = VDDQ = 1.7 to 1.95V - VPPF = 9V for fast program Electronic signature - Manufacturer Code: 20h - Device Code: 8833 ECOPACK(R) package Multiplexed Address/Data Synchronous / Asynchronous Read - Synchronous Burst Read mode: 108MHz, 66MHz - Asynchronous Page Read mode - Random Access: 96ns Programming time - 4.2s typical Word program time using Buffer Enhanced Factory Program command Memory organization - Multiple Bank Memory Array: 64 Mbit Banks - Four Extended Flash Array (EFA) Blocks of 64 Kbits Dual operations - program/erase in one Bank while read in others - No delay between read and write operations Security - 64 bit unique device number - 2112 bit user programmable OTP Cells

FBGA
TFBGA107 (ZAN)
100,000 Program/erase cycles per block Block locking - All Blocks locked at power-up - Any combination of Blocks can be locked with zero latency - WPF for Block Lock-Down - Absolute Write Protection with VPPF = VSS Common Flash Interface (CFI) Multiplexed Address/Data bus Asynchronous operating modes - Random Read: 70ns access time - Asynchronous Write Synchronous modes - Synchronous Read: Fixed length (4-, 8-, 16-, and 32-Word) or continuous burst - Clock Frequency: 83MHz (max) - Synchronous Write: continuous burst Low-power features - Partial Array Self-Refresh (PASR) - Deep Power-Down (DPD) mode - Automatic Temperature-compensated SelfRefresh
Flash memory

PSRAM

November 2007
Rev 0.2
1/23
www.numonyx.com 1
This is preliminary information on a new product now in development or undergoing evaluation. Details are subject to change without notice.
M36P0R9060N0
Contents
1 2 Summary description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Signal descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
2.1 2.2 2.3 2.4 2.5 2.6 2.7 2.8 2.9 2.10 2.11 2.12 2.13 2.14 2.15 2.16 2.17 2.18 2.19 2.20 2.21 2.22 Address Inputs (ADQ0-ADQ15 and A16-A24) . . . . . . . . . . . . . . . . . . . . . . 9 Data Input/Output (ADQ0-ADQ15) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Latch Enable (L) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Clock (K) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Wait (WAIT) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Flash Chip Enable input (EF) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Flash Output Enable inputs (GF) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Flash Write Enable (WF) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Flash Write Protect (WPF) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Flash Reset (RPF) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 PSRAM Chip Enable input (EP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 PSRAM Write Enable (WP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 PSRAM Output Enable (GP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 PSRAM Upper Byte Enable (UBP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 PSRAM Lower Byte Enable (LBP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 PSRAM Configuration Register Enable (CRP) . . . . . . . . . . . . . . . . . . . . . 11 Deep Power-Down input (DPDF) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 VDDF Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 VCCP Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 VDDQ Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 VPPF Program Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 VSS Ground . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
3 4 5
Functional description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Maximum rating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 DC and AC parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
2/23
M36P0R9060N0
6 7 8
Package mechanical . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Part numbering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
3/23
M36P0R9060N0
List of tables
Table 1. Table 2. Table 3. Table 4. Table 5. Table 7. Table 8. Signal names . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Main operating modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Absolute maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Operating and AC measurement conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Capacitance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Ordering information scheme . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Document revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
4/23
M36P0R9060N0
List of figures
Figure 1. Figure 2. Figure 3. Figure 4. Figure 5. Figure 6. Logic diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 TFBGA connections (top view through package) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Functional block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 AC measurement I/O waveform . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 AC measurement load circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 TFBGA 107 8x11mm - 9x12 active ball array, 0.8mm pitch, package outline . . . . . . . . . . 19
5/23
1 Summary description
M36P0R9060N0
1
Summary description
The M36P0R9060N0 combines two memory devices in a Multi-Chip Package:

512-Mbit Multiple Bank Flash memory (the M58PR512JN) 64-Mbit PSRAM (the M69KM096AA).
The purpose of this document is to describe how the two memory components operate with respect to each other. It must be read in conjunction with the M58PRxxxJN and M69KM096AA datasheets, where all specifications required to operate the Flash memory and PSRAM components are fully detailed. Recommended operating conditions do not allow more than one memory to be active at the same time. The memory is offered in a Stacked TFBGA107 package. It is supplied with all the bits erased (set to `1'). Figure 1. Logic diagram
VDDF VDDQ 9 A16-A24 EF GF WF RPF WPF L K DPDF EP GP WP CRP UBP LBP M36P0R9060N0 VCCP
VPPF 16 ADQ0-ADQ15 WAIT
VSS
AI13417
6/23
M36P0R9060N0 Table 1.
A16-A24
(1)
1 Summary description Signal names
Address Inputs Common Data Inputs/Outputs or Address inputs, Command inputs Common Flash and PSRAM Power Supply for I/O Buffers Flash Memory Optional Supply Voltage for Fast Program & Erase Flash Memory Power Supply PSRAM Power Supply Ground Latch Enable input Burst Clock Wait Output Not Connected Internally Do Not Use as Internally Connected
ADQ0-ADQ15 VDDQ VPPF VDDF VCCP VSS L K WAIT NC DU Flash Memory EF GF WF RPF WPF DPDF PSRAM EP GP WP CRP UBP LBP
Chip Enable input Output Enable Input Write Enable input Reset input Write Protect input Deep Power-Down
Chip Enable Input Output Enable Input Write Enable Input Configuration Register Enable Input Upper Byte Enable Input Lower Byte Enable Input
1. A22-A24 are Address Inputs for the Flash memory component only.
7/23
1 Summary description Figure 2.
1
M36P0R9060N0 TFBGA connections (top view through package)
2 3 4 5 6 7 8 9
A
DU
NC
NC
NC
VCCP
DPDF
VSS
DU
B
DU
NC
A18
A19
VSS
VDDF
NC
A21
NC
C
NC
NC
LBP
A23
VSS
NC
K
A22
NC
D
VSS
NC
A17
A24
VPPF
WP
EP
NC
NC
E
VSS
NC
NC
NC
WPF
L
A20
NC
NC
F
NC
NC
NC
UBP
RPF
WF
NC
NC
A16
G
VDDQ
NC
ADQ8
ADQ2
ADQ10
ADQ5
ADQ13
WAIT
NC
H
VSS
GP
ADQ0
ADQ1
ADQ3
ADQ12
ADQ14
ADQ7
NC
J
DU
NC
GF
ADQ9
ADQ11
ADQ4
ADQ6
ADQ15
VDDQ
K
NC
EF
NC
NC
NC
VCCP
NC
VDDQ
CRP
L
DU
VSS
VSS
VDDQ
VDDF
VSS
VSS
VSS
VSS
M
DU
NC
DU
DU
DU
DU
DU
DU
DU
AI13418
8/23
M36P0R9060N0
2 Signal descriptions
2
Signal descriptions
See Figure 1., Logic diagram and Table 1., Signal names, for a brief overview of the signals connected to this device.
2.1
Address Inputs (ADQ0-ADQ15 and A16-A24)
Addresses A0-A21 are common inputs for the Flash memory and PSRAM components. Addresses A22 and A24 are inputs for the Flash memory component only. The Address Inputs select the cells in the memory array to access during Bus Read operations. During Bus Write operations they control the commands sent to the Command Interface of the Program/Erase Controller.
2.2
Data Input/Output (ADQ0-ADQ15)
The Data I/O output the data stored at the selected address during a Bus Read operation or input a command or the data to be programmed during a Bus Write operation.
2.3
Latch Enable (L)
The Latch Enable pin is common to the Flash memory and PSRAM components. For details of how the Latch Enable signal behaves, please refer to the datasheets of the respective memory components: M69KM096AA for the PSRAM and M58PRxxxJN for the Flash memory.
2.4
Clock (K)
The Clock input pin is common to the Flash memory and PSRAM components. For details of how the Clock signal behaves, please refer to the datasheets of the respective memory components: M69KM096AA for the PSRAM and M58PRxxxJN for the Flash memory.
9/23
2 Signal descriptions
M36P0R9060N0
2.5
Wait (WAIT)
WAIT is an output pin common to the Flash memory and PSRAM components. However the WAIT signal does not behave in the same way for the PSRAM and the Flash memory. For details of how it behaves, please refer to the M69KM096AA datasheet for the PSRAM and to the M58PRxxxJN datasheet for the Flash memory.
2.6
Flash Chip Enable input (EF)
The Chip Enable input activates the control logic, input buffers, decoders and sense amplifiers of the Flash memory. When Chip Enable is Low, VIL, and Reset is High, VIH, the device is in active mode. When Chip Enable is at VIH the Flash memory are deselected, the outputs are high impedance and the power consumption is reduced to the standby level. It is not allowed to have EF at VIL and EP at VIL at the same time. Only one memory component can be enabled at a time.
2.7
Flash Output Enable inputs (GF)
The Output Enable input controls the data outputs during Flash memory Bus Read operations.
2.8
Flash Write Enable (WF)
The Write Enable input controls the Bus Write operation of the Flash memory Command Interface. The data and address inputs are latched on the rising edge of Chip Enable or Write Enable whichever occurs first.
2.9
Flash Write Protect (WPF)
Write Protect is an input that gives an additional hardware protection for each block. When Write Protect is Low, VIL, Lock-Down is enabled and the protection status of the LockedDown blocks cannot be changed. When Write Protect is at High, VIH, Lock-Down is disabled and the Locked-Down blocks can be locked or unlocked. (See the Lock Status Table in the M58PRxxxJN datasheet).
2.10
Flash Reset (RPF)
The Reset input provides a hardware reset of the Flash memories. When Reset is at VIL, the memory is in Reset mode: the outputs are high impedance and the current consumption is reduced to the Reset Supply Current IDD2. Refer to the M58PRxxxJN datasheet, for the value of IDD2. After Reset all blocks are in the Locked state and the Configuration Register is reset. When Reset is at VIH, the device is in normal operation. Exiting Reset mode the device enters Asynchronous Read mode, but a negative transition of Chip Enable or Latch Enable is required to ensure valid data outputs. The Reset pin can be interfaced with 3V logic without any additional circuitry. It can be tied to VRPH (refer to the M58PRxxxJN datasheet).
10/23
M36P0R9060N0
2 Signal descriptions
2.11
PSRAM Chip Enable input (EP)
The Chip Enable input activates the PSRAM when driven Low (asserted). When deasserted (VIH), the device is disabled, and goes automatically in low-power Standby mode or Deep Power-down mode, according to the RCR (Refresh Configuration Register) setting.
2.12
PSRAM Write Enable (WP)
Write Enable, WP, controls the Bus Write operation of the PSRAM. When asserted (VIL), the device is in Write mode and Write operations can be performed either to the configuration registers or to the memory array.
2.13
PSRAM Output Enable (GP)
When held Low, VIL, the Output Enable, GP, enables the Bus Read operations of the PSRAM.
2.14
PSRAM Upper Byte Enable (UBP)
The Upper Byte En-able, UBP, gates the data on the Upper Byte Data Inputs/Outputs (DQ8DQ15) to or from the upper part of the selected address during a Write or Read operation.
2.15
PSRAM Lower Byte Enable (LBP)
The Lower Byte Enable, LBP, gates the data on the Lower Byte Data Inputs/Outputs (DQ0DQ7) to or from the lower part of the selected address during a Write or Read operation. If both LBP and UBP are disabled (High), the device will disable the data bus from receiving or transmitting data. Although the device will seem to be deselected, it remains in an active mode as long as EP remains Low.
2.16
PSRAM Configuration Register Enable (CRP)
When this signal is driven High, VIH, bus read or write operations access either the value of the Refresh Configuration Register (RCR) or the Bus Configuration Register (BCR) according to the value of A19.
11/23
2 Signal descriptions
M36P0R9060N0
2.17
Deep Power-Down input (DPDF)
The Deep Power-Down input is used to put the device in a Deep Power-Down mode. When the device is in Standby mode and the Enhanced Configuration Register bit ECR15 is set, asserting the Deep Power-Down input will cause the memory to enter the Deep PowerDown mode. When the device is in the Deep Power-Down mode, the memory cannot be modified and the data is protected. The polarity of the DPD pin is determined by ECR14. The Deep Power-Down input is active Low by default.
2.18
VDDF Supply Voltage
VDDF provides the power supply to the internal core of the Flash memory. It is the main power supply for all Flash memory operations (Read, Program and Erase).
2.19
VCCP Supply Voltage
The VCCP Supply Voltage is the core supply voltage.
2.20
VDDQ Supply Voltage
VDDQ provides the power supply for the Flash memory and PSRAM I/O pins. This allows all Outputs to be powered independently of the Flash memory and PSRAM core power supplies, VDDF and VCCP.
2.21
VPPF Program Supply Voltage
VPPF is both a control input and a power supply pin for the Flash memory. The two functions are selected by the voltage range applied to the pin. If VPPF is kept in a low voltage range (0V to VDDQ) VPPF is seen as a control input. In this case a voltage lower than VPPLK gives an absolute protection against Program or Erase, while VPPF > VPP1 enables these functions (see the M58PRxxxJN datasheet for the relevant values). VPPF is only sampled at the beginning of a Program or Erase; a change in its value after the operation has started does not have any effect and Program or Erase operations continue. If VPPF is in the range of VPPH it acts as a power supply pin. In this condition VPPF must be stable until the Program/Erase algorithm is completed.
12/23
M36P0R9060N0
2 Signal descriptions
2.22
VSS Ground
VSS is the common ground reference for all voltage measurements in the Flashmemory (core and I/O Buffers) and PSRAM chips. It must be connected to the system ground. Note: Each Flash memory device in a system should have their supply voltage (VDDF) and the program supply voltage VPPF decoupled with a 0.1F ceramic capacitor close to the pin (high frequency, inherently low inductance capacitors should be as close as possible to the package). See Figure 5., AC measurement load circuit. The PCB track widths should be sufficient to carry the required VPPF program and erase currents.
13/23
3 Functional description
M36P0R9060N0
3
Functional description
The PSRAM and Flash memory components have separate power supplies but share the same grounds. They are distinguished by two Chip Enable inputs: EF for the Flash memory and EP for the PSRAM. Recommended operating conditions do not allow more than one device to be active at a time. The most common example is a simultaneous read operations on the Flash memory and the PSRAM which would result in a data bus contention. Therefore it is recommended to put the other device in the high impedance state when reading the selected device. Figure 3. Functional block diagram
VDDF VPPF
EF GF A22-A24 WF RPF WPF 512 Mbit Flash Memory DPDF
WAIT L K
A16-A21 VCCP VSS VDDQ
ADQ0-ADQ15
EP GP WP CRP UBP LBP
64 Mbit PSRAM
Ai13419
14/23
M36P0R9060N0 Table 2. Main operating modes(1)
(2)
3 Functional description
Operation
EF GF WF RPF
DPDF
(3)
WAIT
(4)
A16, UBP A17, CRP A19 A18 L EP WP GP LBP A20, A21 VIH VIH VIL PSRAM must be disabled
ADQ15ADQ0
Bus Read Bus Write Flash memory Address Latch Output Disable Standby Reset
VIL VIL VIH VIH VIL VIH VIL VIH VIL VIH VIH VIH VIL VIH VIH VIH VIH X X X X X X VIH VIL VIH
dea(5) dea(5) dea(5) dea(5) dea(5) dea(5) assert ed(7) Hi-Z Hi-Z Hi-Z Hi-Z
Data Output Data Input Data Output or Hi-Z(6) Hi-Z Hi-Z Any PSRAM mode is allowed Hi-Z Hi-Z Address In/ Data Out Valid Address In/ Data In Valid Address In/ BCR, RCR or DIDR Content Valid High-Z High-Z High-Z
VIH X X X
Deep Power-Down VIH X Read
VIH VIL VIL VIL VIH VIL VIL
VIL Address In Valid VIL Address In Valid
Write Flash memory must be disabled PSRAM Read CR (CR controlled method)
\_/
00(RCR) 10(BCR) VIH VIL VIL VIH X1(DID R) VIH X X X X VIL X X X X VIL X X X
X
Output Disable/No Operation Deep PowerDown(8) Standby
1. X = Don't care, de-a. = de-asserted, CR = Configuration Register.
X X X
Any Flash memory mode is allowed
XV IH X VIH X
X X
2. The Clock signal, K, must remain Low in asynchronous operating mode. 3. The DPD signal polarity depends on the value of the ECR14 bit. 4. WAIT signal polarity is configured using the Set Configuration Register command. 5. If ECR15 is set to '0', the device cannot enter the Deep Power-Down mode, even if DPD is asserted. 6. Depends on G. 7. ECR15 has to be set to `1' for the device to enter Deep Power-Down. 8. The device enters Deep Power-Down mode by driving the Chip Enable signal, E, from Low to High, with bit 4 of the RCR set to `0'. The device remains in Deep Power-Down mode until E goes Low again and is held Low for tELEH(DP).
15/23
4 Maximum rating
M36P0R9060N0
4
Maximum rating
Stressing the device above the rating listed in the Absolute Maximum Ratings table may cause permanent damage to the device. These are stress ratings only and operation of the device at these or any other conditions above those indicated in the Operating sections of this specification is not implied. Exposure to Absolute Maximum Rating conditions for extended periods may affect device reliability. Refer also to the Numonyx SURE Program and other relevant quality documents. Table 3.
Symbol TA TBIAS TSTG VIO VDDF VCCP VDDQ VPPF IO tVPPH
Absolute maximum ratings
Value Parameter Min Ambient Operating Temperature Temperature Under Bias Storage Temperature Input or Output Voltage Flash Memory Supply Voltage PSRAM Supply Voltage Input/Output Supply Voltage Flash Memory Program Voltage Output Short Circuit Current Time for VPPF at VPPH -30 -30 -55 -0.2 -1.0 -0.2 -0.2 -1 Max 85 85 125 2.45 3.0 2.45 2.45 11.5 100 100 C C C V V V V V mA hours Unit
16/23
M36P0R9060N0
5 DC and AC parameters
5
DC and AC parameters
This section summarizes the operating measurement conditions, and the DC and AC characteristics of the device. The parameters in the DC and AC characteristics Tables that follow, are derived from tests performed under the Measurement Conditions summarized in Table 4., Operating and AC measurement conditions. Designers should check that the operating conditions in their circuit match the operating conditions when relying on the quoted parameters. Table 4. Operating and AC measurement conditions
Flash Memory Parameter Min VDDF Supply Voltage VCCPSupply Voltage VDDQ Supply Voltage VPPF Supply Voltage (Factory environment) VPPF Supply Voltage (Application environment) Ambient Operating Temperature Load Capacitance (CL) Impedance Output (Z0) Output Circuit Protection Resistance (R) Input Rise and Fall Times Input Pulse Voltages Input and Output Timing Ref. Voltages 3 0 to VDDQ VDDQ/2 1.7 - 1.7 8.5 -0.4 -30 30 50 50 2 0 to VDDQ VDDQ/2 Max 1.95 - 1.95 9.5 VDDQ +0.4 85 Min - 1.7 1.7 - - -30 30 Max - 1.95 1.95 - - 85 V V V V V C pF ns V V PSRAM Unit
Figure 4.
AC measurement I/O waveform
VDDQ VDDQ/2 0V
AI06161
17/23
5 DC and AC parameters Figure 5. AC measurement load circuit
VDDQ/2
M36P0R9060N0
R DEVICE UNDER TEST
OUT Z0 CL
AI13228
1. VDD means VDDF = VCCP.
Table 5.
Symbol CIN COUT
Capacitance(1)
Parameter Input Capacitance Output Capacitance Test Condition VIN = 0V VOUT = 0V Min - - Max 14 14 Unit pF pF
1. Sampled only, not 100% tested.
Please refer to the M58PRxxxJN and M69KM096AA datasheets for further DC and AC characteristics values and illustrations.
18/23
M36P0R9060N0
6 Package mechanical
6
Package mechanical
In order to meet environmental requirements, Numonyx offers these devices in ECOPACK(R) packages. These packages have a Lead-free second level interconnect. The category of second Level Interconnect is marked on the package and on the inner box label, in compliance with JEDEC Standard JESD97. The maximum ratings related to soldering conditions are also marked on the inner box label. Figure 6. TFBGA 107 8x11mm - 9x12 active ball array, 0.8mm pitch, package outline
D D1 FD
e
E E1
BALL "B1"
SE
ddd
FE A e b A1 A2
BGA-Z85
1. Drawing is not to scale.
19/23
6 Package mechanical Table 6.
M36P0R9060N0 Stacked TFBGA107 8x11mm - 9x12 active ball array, 0.8mm pitch, package data
millimeters inches Max 1.20 0.20 0.85 0.35 8.00 6.40 0.10 11.00 8.80 0.80 0.80 1.10 0.40 10.90 11.10 0.433 0.346 0.031 0.031 0.043 0.016 0.429 0.30 7.90 0.40 8.10 0.033 0.014 0.315 0.252 0.004 0.437 0.012 0.311 0.016 0.319 0.008 Typ Min Max 0.047
Symbol Typ A A1 A2 b D D1 ddd E E1 e FD FE SE Min
20/23
M36P0R9060N0
7 Part numbering
7
Part numbering
Table 7.
Example: Device Type M36 = Multi-Chip Package (Flash + PSRAM) Flash 1 Architecture P = Multi-Level, Multiple Bank, Large Buffer Flash 2 Architecture 0 = No Die Operating Voltage R = VDDF = VCCP = VDDQ = 1.7 to 1.95V Flash 1 Density 9 = 512 Mbits Flash 2 Density 0 = No Die RAM 1 Density 6 = 64 Mbits RAM 2 Density 0 = No Die Parameter Blocks Location N = Even Block Flash Memory Configuration, Mux I/O Product Version 0 = 90nm Flash technology, 96ns speed; 0.11m PSRAM technology, 70ns speed Package ZAN = stacked TFBGA107 C stacked footprint. Option E = ECOPACK Package, Standard packing F = ECOPACK Package, Tape & Reel packing
Ordering information scheme
M36 P 0 R 9 0 6 0 N 0 ZAC E
Note:
Devices are shipped from the factory with the memory content bits erased to '1'. For a list of available options (Speed, Package, etc.) or for further information on any aspect of this device, please contact the Numonyx Sales Office nearest to you.
21/23
8 Revision history
M36P0R9060N0
8
Revision history
Table 8.
Date 21-Jul-2006 30-Nov-2007
Document revision history
Revision 0.1 0.2 Initial release. Applied Numonyx branding. Changes
22/23
M36P0R9060N0
Please Read Carefully:
INFORMATION IN THIS DOCUMENT IS PROVIDED IN CONNECTION WITH NUMONYXTM PRODUCTS. NO LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THIS DOCUMENT. EXCEPT AS PROVIDED IN NUMONYX'S TERMS AND CONDITIONS OF SALE FOR SUCH PRODUCTS, NUMONYX ASSUMES NO LIABILITY WHATSOEVER, AND NUMONYX DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY, RELATING TO SALE AND/OR USE OF NUMONYX PRODUCTS INCLUDING LIABILITY OR WARRANTIES RELATING TO FITNESS FOR A PARTICULAR PURPOSE, MERCHANTABILITY, OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. Numonyx products are not intended for use in medical, life saving, life sustaining, critical control or safety systems, or in nuclear facility applications. Numonyx may make changes to specifications and product descriptions at any time, without notice. Numonyx, B.V. may have patents or pending patent applications, trademarks, copyrights, or other intellectual property rights that relate to the presented subject matter. The furnishing of documents and other materials and information does not provide any license, express or implied, by estoppel or otherwise, to any such patents, trademarks, copyrights, or other intellectual property rights. Designers must not rely on the absence or characteristics of any features or instructions marked "reserved" or "undefined." Numonyx reserves these for future definition and shall have no responsibility whatsoever for conflicts or incompatibilities arising from future changes to them. Contact your local Numonyx sales office or your distributor to obtain the latest specifications and before placing your product order. Copies of documents which have an order number and are referenced in this document, or other Numonyx literature may be obtained by visiting Numonyx's website at http://www.numonyx.com. Numonyx StrataFlash is a trademark or registered trademark of Numonyx or its subsidiaries in the United States and other countries. *Other names and brands may be claimed as the property of others. Copyright (c) 11/5/7, Numonyx, B.V., All Rights Reserved.
23/23

▲Up To Search▲

Price & Availability of M36P0R9060N0ZANE

	To Download M36P0R9060N0ZANE Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .